How are y’all doing this week? Getting ready for the holidays? Instead of decorating, we did some demolition in the kitchen this past weekend. And it involved buying myself an early Christmas present:
I snatched up this DEWALT 10–Amp Keyless Variable Speed Corded Reciprocating Saw that was on sale at Lowe’s. I actually held each and every reciprocating saw in the tool department. Those saws are not lightweight by any means. And since I had to hold this over my head and make repeated cuts, I wanted to make sure I bought the lightest one I could find. However, I had one other factor to contend with. Battery life! The lightest weight saw was a Ni-Cad battery saw and I didn’t want to deal with losing power in the middle of the job and waiting for the battery to charge up again. So, I chose this mid-weight fighter because it has a cord and it won’t run out of power…ever…well unless your power goes out. I’m thrilled with its performance, this prize winning middle weight really knows how to throw a knock down punch to soffits.
AND, in a pinch, it works great as a turkey carver (LOL!)
I also took advantage of those fabulous Black Friday sales at Lowe’s and bought two of these
Werner Aluminum Work Platforms:
They were invaluable because we didn’t have to climb ladders or use the saw over our heads (not a good idea.) And now we are using one of those platforms as a stand in bench where I want to build a window seat. 😉
Here’s how we tackled those ceiling hugger – space waster – height crowding – good for nuthin’ – you get the picture soffits:
- Reciprocating saw
- Platform stand
- Hand saw
- Skinny pry bar
- Larger pry bar
- Dust mask
- Ear muffs
- Eye goggles
- Utility knife
- Voltage tester
- Sledge hammer
- Work gloves
- Trash can with heavy duty black plastic bags
The number one priority is to turn off the power to any and all circuits that are live in the kitchen.
And, double check them with a voltage detector.
The Greenlee Non-Contact Volt Detector I bought tests current even through the coating on the wire. Thank goodness I used this because we actually found one wire that was still live after all the kitchen circuits were turned off.
Knock a head sized hole in the end of your soffit. Shine a flashlight inside to see what you have to work with. Our soffit has a few wires, an angled plumbing stack and a recessed light fixture.
In the next soffit, we knew there was an exhaust pipe inside.
We carefully marked the locations of anything to avoid before proceeding, to minimize damage to them (and us.)
Removing the crown molding:
To preserve the crown molding for future use, score the top and bottom of the molding to cut through the caulk.
Use a skinny flat pry bar and gently hammer it under the base of the crown molding (the molding will usually only be nailed to the soffit not the ceiling.) Continue working from one side to the other prying up the molding.
Demolition of the Soffits:
Remove any cabinets that are touching the soffit. Usually cabinets are nailed or screwed to studs through the back. Inspect your cabinets to determine how they are fastened.
(Yup, that is all one cabinet…14 feet long! When we donated it to our local Habitat ReStore they told us that’s the longest single cabinet they’d ever seen.)
Remove any light fixtures, cap off the wires and gently tuck the wires out of harm’s way.
Put on your safety gear (ear muffs, dust mask, and eye goggles) because things are about to get messy! Use a hammer to break up the drywall (sometimes referred to as sheetrock.) Continually check for more wires or plumbing pipes. Check all wires as you uncover them to make sure they aren’t live.
Then you could let the kids go to town with hammers. (Our boys did most of the drywall removal for us. It was a perfect task for them to do with a lot of supervision.)
We wheeled the trashcan right into the kitchen and filled up 3 bags of sheetrock (drywall)!
By removing the drywall, we could see the skeleton of the soffit and any obstacles that needed to be avoided when using the reciprocating saw. Plus, the weight of the soffit is drastically reduced without that extra weight.
Our plan of attack involved cutting through the vertical 2×4 studs. Then make one cut about 4-5 feet along the soffit.
First Handsome Guy cut through the vertical members.
Then he cut down through the horizontal board to section the soffit into a manageable chunk.
At this point I was getting jealous that he was spending too much time with my new power tool. My turn!
Cutting was pretty easy. Just be sure to have a wide stance when the stud finally gives way to the saw.
There was one spot that required a handsaw because I didn’t want to risk cutting the electrical wire.
Then we yanked and pulled with all our might. We used a pry bar and hammer to loosen the soffit further from the wall. Eventually the soffit gives up and let’s go of its grip on the wall. It’s a good idea to have your helper nearby to catch the soffit (or you! Careful you don’t fall off the platform.)
Once the exhaust pipe was exposed, I pulled it out easily (it wasn’t screwed to anything and slipped off like an old man’s stretched out sock.)
The center soffit was removed by Pretty Handsome Guy with the help of a sledgehammer and a cheering crowd of young boys watching:
Our boys think Dad is a rock star now! “Go Daddy Go! Hit it again, Dad!”
The center soffit came down remarkably easily, teasing us into thinking the rest would be a cinch.
The other two soffits were supported by the wall behind it. We used the hammer and pry bar to pry the top and back boards off the wall and ceiling. Keeping the pry bar in line with studs and floor joists gave us the leverage needed to pull it off.
And now for the drastic before and after shots:
It’s a beautiful piece of work isn’t it? Having the soffits removed is a great feeling. I love that the ceilings feel taller already. Never mind that our walls and ceiling look like swiss cheese.
In the immortal words of Bing Crosby: “You gotta ACK-cent-tchuate the positive. E-lim-inate the Negative…Latch on to the affirmative and don’t mess with Mr. InBetween!”
We’ll be doing a lot of not messing with Mr. InBetween while we wait for the next phase to begin. Adios!
You can read more about our kitchen disaster and renovation in these updates:
- Polybutylene Pipe Leak turns into Moldy Mess
- My World Upended, Asbestos Discovery and Removal -All You Ever Wanted to Know About Asbestos
- Planning New Kitchen Layout and more
- Planning Colors and Materials for the New Kitchen
- Let the Demolition Begin
- Move Back in the Kitchen Temporarily and Throw a New Year’s Party
- Termite Damage and Kitchen Update
- How and When You Should File for a Permit during a Kitchen Renovation – Your Questions Answered
- Everything You Should Know about Termites and Termite Damage
- Structural Engineer Plans and another Kitchen Update
- How to Survive without a Kitchen During Renovation
Disclosure: Some of the links above are affiliate links for your convenience. I do receive a very small percentage if you chose to purchase any of the DIY tools that I link to.