Sharing is caring!

Toilet Repairs Replacing the Overflow Tube and Flapper

I’ve received a few emails and comments letting me know that some of you are going to try to repair your toilets! I just wanted to say, way to go! Plus, some of you had a few questions for me as well.

Here are the questions:

1. Our 1/2 bath toilet seems to chronically clog. We use enzyme stuff to clear it but it just clogs again the next time someone does anything substantial in it. It’s annoying. Any tips?

A. Adjust the amount of water in the tank so it will give more H20 to flush (as shown at the end of Toilet Repairs Part 2). Or use a good accordian style plunger:

Toilet Repairs Replacing the Overflow Tube and Flapper

If all else fails, you may have a clog and need to snake your toilet out. I’ve seen some snakes that attach to a drill.

Toilet Repairs Replacing the Overflow Tube and Flapper

Just be careful you don’t scratch the bottom of your toilet bowl when snaking it.

2. What are the symptoms for needing a new fill valve? On ours, you have to push the flush handle down really hard and hold it… or it won’t flush at all on first flush sometimes. Thanks for the great tutorials!

A. It sounds like you either need a new flapper or you might try tightening the chain between the flapper and the lever rod. If you need to replace the flapper, you should probably replace the entire overflow tube/flapper assembly.

And that leads me to today’s tutorial!

How to replace the overflow tube and flapper:

In review, here is what your toilet tank parts are:

Toilet Repairs Replacing the Overflow Tube and Flapper

And here is the kit I recommend you purchase (costs about $20):

Toilet Repairs Replacing the Overflow Tube and Flapper

And here are the tools you will need:

Toilet Repairs Replacing the Overflow Tube and Flapper

  • Plumber’s Wrench (must have a wide mouth opening. The Irwin pliers shown have just enough of an opening to work)
  • Adjustable Crescent Wrench
  • Handsaw (drywall, coping or hack saw will work. Needs to cut through PVC)
  • Flat head screwdriver
  • Level
  • Scissors
  • Bucket or basin
  • Sponge
  • Rags or Towels
  • Rubber Gloves

Disclaimer: This tutorial is a general overview of replacing an overflow tube and flapper in your toilet tank. Be sure to follow the directions that come with your toilet parts as there may be changes or additional steps.

If you haven’t done so already, start by turning off the water. There should be a water shut off valve in the wall behind your toilet. Gently turn the knob clockwise to shut the valve.

Toilet Repairs Replacing the Overflow Tube and Flapper

Next, flush your toilet to drain the water from the tank. If your tank re-fills the water is not completely shut off.

Toilet Repairs Replacing the Overflow Tube and Flapper

Remove the lid to your tank. Set it in a safe place where it can’t get dropped and broken.

Toilet Repairs Replacing the Overflow Tube and Flapper

If there is still a lot of water in the bottom of the tank. Lift the flapper chain to drain the tank to the top of the flapper.

Toilet Repairs Replacing the Overflow Tube and Flapper

Use a sponge to completely soak up all the water remaining in the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Once the tank is completely empty we can start to remove the overflow tube and flapper. But, first you need to disconnect the water supply tube. Because TODAY we are going to take the entire tank off! Don’t be freaked out, you can do this. It is just like unscrewing the screws and removing a light switch cover (only it weighs a lot more.)

Look underneath the tank to see where the water line feeds into the tank. Using pliers, loosen and then remove the coupling nut from the supply line.

One quick note about supply lines: If your toilet has a plastic or rubber supply line, you should consider replacing it with a braided metal supply line that is less prone to breaking or leaks (in other words they can cause a major flood!) The same advice applies to the water lines under your sink and definitely your clothes washer.

Toilet Repairs Replacing the Overflow Tube and Flapper

Place the basin or bucket underneath the supply line and gently remove the line from the bottom of the fill valve (gray threaded stem shown below.)

 

Toilet Repairs Replacing the Overflow Tube and Flapper

Detach the chain from the lever rod inside the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Remove the rubber gasket by lifting up the sides of the flaps. If your gasket is attached a different way, don’t worry about it, just leave it attached.

Toilet Repairs Replacing the Overflow Tube and Flapper

Disconnect the water refill hose from the overflow tube by sliding the anchor hook up and off the overflow.

Toilet Repairs Replacing the Overflow Tube and Flapper

Use your flat head screwdriver to lose the bolts at the bottom of the tank (on either side of the flapper.) You may need to reach underneath and hold the nut (or wing nut) with pliers as the bolt begins to loosen.

Toilet Repairs Replacing the Overflow Tube and Flapper

Toilet Repairs Replacing the Overflow Tube and Flapper

Once the nut (or wing nut) has been removed, you can now lift the tank off the toilet (using both hands.) Ask for help if you are concerned about possibly dropping the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

I recommend draping a towel over the toilet seat lid to rest the tank onto.

Remove the rubber gasket in the center of the underside of your tank. You may want to wear gloves (not because of germs, but because the rubber may be deteriorating and can leave black on your hands. But, come to think about it, I have two little boys and their aim isn’t exactly spot on. If you know what I mean.)

Toilet Repairs Replacing the Overflow Tube and Flapper

Now you need to remove the two bolts that held the tank to the toilet base. Loosen the nut with the pliers or crescent wrench.

Toilet Repairs Replacing the Overflow Tube and Flapper

Remove the nut and washer.

Toilet Repairs Replacing the Overflow Tube and Flapper

Repeat to remove the other bolt.

Toilet Repairs Replacing the Overflow Tube and Flapper

Grab the pliers and loosen the large plastic hex nut that was under the gasket. Then remove the nut. (I’m very thankful that the Irwin Adjustable Hex pliers I have worked perfectly. Otherwise, I would have had to buy a pair of plumbing pliers.)

Toilet Repairs Replacing the Overflow Tube and Flapper

Now you can remove the overflow tube and flapper assembly from the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

If you are replacing all the parts in your tank at once, when the tank is empty is a great time to give it a good cleaning!

Toilet Repairs Replacing the Overflow Tube and Flapper

Okay, time to put Frankenstein back together again. Grab the new overflow tube and flapper assembly from your kit. Insert the new overflow tube back into the toilet tank. Make sure it is sitting flush against the bottom of the tank (you may need to tilt the tank for it to feed all the way through.) Then set your level up to the line indicated on the fill valve. Make a mark on the overflow tube one inch lower than the mark on the fill valve..

Toilet Repairs Replacing the Overflow Tube and Flapper

Cut the top of your overflow tube off using a saw. Sand any rough edges if necessary.

Toilet Repairs Replacing the Overflow Tube and Flapper

Re-insert the flush valve (overflow tube & flapper assembly) into the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Thread the new hex nut onto the bottom of the overflow tube and hand tighten it.

Toilet Repairs Replacing the Overflow Tube and Flapper

Because I don’t possess the masculine type strength, I use my pliers to turn the hex nut another half a turn until it is snug but not tight enough to crack the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Fit the new rubber gasket over the hex nut as shown below.

Toilet Repairs Replacing the Overflow Tube and Flapper

Insert two new bolts into the tank with a rubber washer just below the head of the bolt.

Toilet Repairs Replacing the Overflow Tube and Flapper

Toilet Repairs Replacing the Overflow Tube and Flapper

Thread a metal washer and a nut onto the bolts from the underside of the tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Gently tighten the nut with the crescent wrench. I can’t stress enough how important it is not to overtighten the nut. Or you will crack your toilet tank.

Toilet Repairs Replacing the Overflow Tube and Flapper

Repeat the same steps to insert the other bolt. The bottom of your tank should look like this:

Toilet Repairs Replacing the Overflow Tube and Flapper

Carefully replace the tank back onto the toilet base. Being sure to line up the bolts with the holes on the toilet.

Toilet Repairs Replacing the Overflow Tube and Flapper

Set a level on top of the tank and level it.

Toilet Repairs Replacing the Overflow Tube and Flapper

Thread the rubber washer, metal washer and then the new wing nut onto the bottom of the bolt. Tighten the wing nuts on both sides. All the while keep an eye on the tank to make sure it stays level.

Toilet Repairs Replacing the Overflow Tube and Flapper

Attach the flapper chain back onto the lever rod. Make sure there is a slight amount of slack in the chain, but not too much. Trim any excess chain that hangs too close to the flapper.

Toilet Repairs Replacing the Overflow Tube and Flapper
Attach the water refill hose to the over flow tube by sliding the anchor clip back onto the overflow tube..

Toilet Repairs Replacing the Overflow Tube and Flapper

Re-attach the water supply line making sure the coupling nut is nice and snug.

Toilet Repairs Replacing the Overflow Tube and Flapper

Toilet Repairs Replacing the Overflow Tube and Flapper

Turn on the water supply to refill the tank. Test the toilet by flushing it. Make sure the flapper closes and nothing holds it open. Replace the tank lid and enjoy your fully functioning toilet!

Toilet Repairs Replacing the Overflow Tube and Flapper

Hey, thanks for sticking with me through this “ugly” but necessary tutorial series. Hopefully I haven’t scared you off (judging from the very few comments I received.) I promise I have some more “attractive” tutorials coming soon. Then you can bring back your wonderfully sweet comments.

55 replies
  1. Monique
    Monique says:

    You’re web site should be called “Amazing” Pretty Handy Girl but I guess that title would be a trifle long. Love the tutorials.

    Reply
    • andrew
      andrew says:

      I was unable to remove fill valve after I remove the nut at the bottom of the toilet and the plastic washer but it won’t budge I don’t understand HELP

      Reply
  2. Pearl
    Pearl says:

    I have a glacier bay water saving toilet with a fill valve similar to fluidmaster you use. It is very slowly filling the tank, much slower than the exact same toilet installed in another bathroom. Before messing with the fill vave, I checked the water valve underneath the tank and the pressure is good going into the tank. Then I removed the cap and unscrewed the top of the fill valve (counterclockwise), planning to flush it. However, I didn’t even need a cup because there is almost no water pressure coming from the fill valve, even with the cap off. There is just barely a trickle of water flowing from it. Something must be wrong in the fill valve tube, but with no water pressure, how do I fix it. The toilet is almost new, so I really don’t want to replace the fill valve or the toilet. Any suggestions?

    Reply
  3. Deb McCarthy
    Deb McCarthy says:

    Thanks so much for the step by step procedure and the pictures – I have not done much in the way of plumbing but think I can do it with your instructions. I am going to try to replace the guts of a toilet that has never been right for 18 years and is very close to failing completely.

    Reply
  4. Ella
    Ella says:

    Brittany,
    I am a newcomer to your sight- but found it to be very informative.
    I will be replacing my toilet flush valve system this weekend, because it is needed and I now have directions on how to do it.
    Thanks Again
    Ella

    Reply
  5. Allana
    Allana says:

    This is an awesome page! Excellent pictures and directions!

    I was thinking we couldn’t install a new flapper with our toilet because we have a really old style flapper valve where the overflow tube is actually centered in the flapper mechanism. First research gave me the impression that the overflow tube was connected to a separate hole than the flapper, but based on your pictures here, we can get a new overflow tube and flapper and install both.

    Now the hard part will be getting the old flapper mechanism out!

    Reply
  6. cheryl yannello
    cheryl yannello says:

    Thank you for being so accurate with your advice and for supplying pictures. It is about time that someone has decided to help the females who are doing their own handypersons job. Thanks so much!!!

    Reply
  7. Andrew Parks
    Andrew Parks says:

    First of all, your tutorial is great, especially the way each part is labeled! I’ve done a similar installation on my toilets, but I used the 460/451 kit from MJSI. I didn’t need any tools to install it, though you might need pliers in order to remove the handle.
    Thanks again for sharing this tutorial!

    Reply
  8. Gayle
    Gayle says:

    How do you level the tank? Our tank keeps filling a small amount at random times when no one had been using it. What does that mean? I cleaned around the new flapper, and it’s still happening. Thanks for the great tutorials!

    Reply
  9. Terry
    Terry says:

    I have a very unique toilet in that it has a separate overflow pipe. There is a soft (sponge rubber) gasket that fits around the bottom of the pipe where it meets the stool. This gasket is distorted and leaks when the water is released from the tank. I can’t find this gasket anywhere. I have tried sealing it by molding a standard wax-ring around the pipe. This worked for a few weeks; but it is leaking again – only a tiny bit when flushed. Any suggestions would help. Thanks.

    Reply
  10. Emma Waters
    Emma Waters says:

    Hi Brittany!

    We at Fluidmaster are so glad to hear that you fixed your toilet with our Complete Toilet Repair Kit! Also, we would like to thank you for sharing your project with others looking for toilet repair help!

    If any of your subscribers would like more information on how to install our other products, they can go to the Fluidmaster website and check out our installation videos and instructions.
    http://www.fluidmaster.com/do-it-yourself/videos

    Thank you Pretty Handy Girl!

    -Emma

    Reply
  11. Eric
    Eric says:

    Great tutorial, thanks! The large number of pictures is really helpful. I was in the midst of repairing the fill valve in my toilet, and the old (copper) overflow tube just snapped right off in my hand when I attached the clip to it! But this page makes it look straightforward to replace that, too – might as well do it all while I have the water disconnected. Thanks again.

    Reply
  12. Ted
    Ted says:

    Thanks for this tutorial. My wife asked me to replace the flapper valve with some new thing that is supposed to stop leaks, which seemed easy. Until I promptly broke the overfill tube, lol. I had replaced the flapper and fill valve before, butt his seemed like a bridge too far. But I read through this tutorial, and was able to replace everything. Thanks again, this was very helpful!!

    Reply
  13. Joe M
    Joe M says:

    Just a hint, make sure when you install the new fill valve that you don’t just insert the small bowl filler tube too far down in the overflow tube. This will cause the water to siphon through the fill valve and constantly leak. The bowl filler tube should have a one inch air-gap above the overflow tube to prevent siphoning and a cross connection.

    Reply
  14. Fred
    Fred says:

    Before I start replacing the overflow assembly your instructions show cutting the overflow pipe one inch ‘below the water line, would this not keep water running down the tube? It looks like the tube should be one inch “higher” than the high water level. Please reply. Thanks Fred

    Reply
    • Brittany Bailey
      Brittany Bailey says:

      Fred, re-read the directions. It says to make a mark on the overflow tube one inch lower than the mark on the fill valve. Not the waterline. This is per Fluid Master systems directions. The Fill Valve is already pre-set to stop the water below that mark, but you can adjust the amount of water in your tank later on.

      Reply
  15. Rupak
    Rupak says:

    Hi ,

    I replaced my 2 toilet flush with universal fluidmaster kit. I followed the same steps, as mentioned in here, however I am still getting running water in both the bowls. Not so much but still the water is running continuously. Its running in both the toilets, so I am guessing I did something wrong. I did use the leveler though, can that be the reason or it may be the siphony of water in the overflow tube.

    Please let me know.

    thanks

    Reply
  16. Sarah
    Sarah says:

    Thank you for the toilet tutorial! I replaced the whole set of tank innards. Though the kit came with instructions, I found your photos to be invaluable in interpreting the instruction. It all went off without a hitch and now we are once again flushing happily!

    Reply
  17. Michelle
    Michelle says:

    Great tutorial! Had this up on my computer as I worked on my Gerber toilet last night… all I have to say is, when the kit directions say they recommend a different flush valve gasket for a certain toilet/tank model – listen! 🙂 Good news – fill valve and water supply weren’t leaking. Bad news – Gerber toilets have a thicker gasket (you can find at Lowe’s – no endorsement meant, just where I found it) that will prevent leaking when you flush (it’s fine as long as you don’t flush) … as I found out last night and laughed as I mopped it up.

    A tip for removing water in tank – a wet-dry vac is awesome in this situation. Especially if the parts in your tank have degraded and you have sludge in there.

    Thank you Pretty Handy Girl!

    Reply
  18. jan skid
    jan skid says:

    I have been replacing the guts of an old toilet. copper overflow and all metal base and threads on the flush valve. Wanted to just replace water filler but replacement part was way to short for very tall overflow which promptly broke off when I tried to cut it down. So I have disassembled all (great instruction, thanks) until I got to the hex nut on the tank bottom. With the tank upside down and looking down on it I can see the hex is next to the tank but there appears to be a large round metal washer over top of the hex. It is either stuck fast, threaded on or a part of the hex. Unfortunately I have no wrench large enough to get a grip on the whole works, off to the hardware store tomorrow. Any idea if the metal ring should come loose independently of if it is a part of the hex?

    Reply
  19. Rose Mitchell
    Rose Mitchell says:

    1/2 the time I flush the toilet the flapper doesn’t go in the hole and my toilet runs, which makes the water company very happy but not me, Please help me, what is the problem?

    Reply
    • Brittany Bailey
      Brittany Bailey says:

      Rose, did you follow this tutorial and install a new flapper and overflow tube? If so, you might need to try a new one. Or check to make sure the chain attached to the handle isn’t getting caught in the flapper.

      Reply
  20. August Mohr
    August Mohr says:

    Thanks for the advice, photos, steps, and encourgagement.

    However, in my case it was not as easy as a light switch cover because one of the bolts holding the tank to the base was frozen. We had two people, my partner holding the wrench on the nut below and me with a giant screwdriver on the top. The tools were not slipping, but our combined might did not break the grip the nut had on the bolt, even with some Liquid Wrench on it.

    I finally got out my Dremel tool that I have for crafting and put a cutting disk on it. I tried cutting a slot in the nut. I didn’t get all the way through, but maybe the vibration got the Liquid Wrench working because eventually it gave and we got it out. And the kit had two fresh bolts.

    Reply
  21. children
    children says:

    Your relationship together with your child will be the longest and many
    important relationship you may ever have. Many solicitors
    practice over different areas of regulations, nevertheless you may think
    that it is safer to retain an attorney that is a professional
    on divorce. When looking at the economics only,
    however, forgetting about the emotionality, there ought to be almost no fighting relating
    to the spouses on this particular subject as
    it is often usually always better, particularly in a declining market, for starters spouse to permit the opposite to keep your family residence to acquire being bought out.

    Reply
  22. Joyce
    Joyce says:

    To the lady who asked the first question about the constant clogging: She may have had someone come in and replace the “guts” of an old toilet (3.5 gal flush) with newer components which are made for the low-flow toilets. (Don’t get me started on low flow toilets and the damage they have done in cities that have a long run to the sewer main!!!!!)

    Be very careful with just replacing things. If you have an older toilet, ALWAYS consider repair (and even fabrication of a component) before replacement.

    Reply
  23. Sandy Luna
    Sandy Luna says:

    Help! I have replaced all the parts in the tank and everything seems to work perfectly, after flushing the tank will fill to right level and stop. I see no leaks or anything but a couple of hours later the water level has risen above the overflow pipe and starts dripping into the toilet. This was the reason I replaced all the parts originally . Do you have any idea what could be causing this?

    Reply
  24. Stephanie
    Stephanie says:

    You are wonderful. I used your instructions to completely replace the innards of my mom’s toilet and it has never worked better. Thank you so much.

    Reply
  25. mike newman
    mike newman says:

    Thanks!

    One of the very few explanations I found online that has useful pictures of all the important steps and clear explanations… instead of long videos of useless chatter.

    Turns out my problem was that the instructions for the kit I have gave the wrong order of washers&nuts to fasten the tank to the bowl. But when I do it your way, it doesn’t leak!

    Reply
  26. Donna
    Donna says:

    Thank u so much for this website. I just bought my first home after my husband passed. He used to do all the repairs. I was able to replace everything in both my toilets with ease. Only trouble I had was figuring out which way tightens and which way loosens. lol Both toilets needed to have taller overflow pipes so that they would flush more effectively. Second bathroom only took 1 hour. Thank you Thank you Thank you. Next I am installing a ceiling fan in bedroom. Any hints? Just kidding

    Reply

Trackbacks & Pingbacks

  1. […] Today we will get your feet wet (no pun intended) by replacing the handle also known as the flush lever. Then I will show you how to replace the fill valve and finally how to replace the overflow tube and flapper assembly. […]

  2. […] you won’t find today’s tutorial too difficult. And then, you will certainly be able to replace the overflow tube and flapper in my next […]

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *